New 730D

Specifications

Compare >>> Select up to 2 models to compare specifications

John Deere730D

Add Model --Please Select-- 725D (Model year 2022) 735D (Model year 2022) 740D (Model year 2022) 94C - 30,36,40,42 2142 2152 2162 3152 Rigid (2018) 3152 Rigid (30-ft) DH-30 4030 SP30 D50-30ft D60-30ft D130 D65 Rigid (30-ft)

Add Model --Please Select-- 725D (Model year 2022) 735D (Model year 2022) 740D (Model year 2022) 94C - 30,36,40,42 2142 2152 2162 3152 Rigid (2018) 3152 Rigid (30-ft) DH-30 4030 SP30 D50-30ft D60-30ft D130 D65 Rigid (30-ft)

Cutterbar length	9.3 m 30.5 ft
Knife drive	Base: dual knife Optional: single
Knife speed	490 cycles/min
Pickup reel operating speeds	6-45 rpm 137.2-cm (54-in.) reel: 5-44 rpm
Draper belts speed control	Hydraulic from cab

Type	Rigid draper

Type	Straight-line knife drive system
Length	9.14 m 30 ft
Knife drive	Base: dual knife Optional: single
Knife speed	490 cycles/min
Cutterbar tilt	Base: hydraulic, maximum tilt 9 degree (angle)
Base skid shoe height

General
Number of slats	Base: six bat poly Optional: eight bat steel (for forage conditions)
Fingers	Base: nylon Optional: steel
Diameter	1.067 m 3.5 ft
Height control	Hydraulic
Speed control	Hydraulic
Reel lift	Cylinder stroke: 330 mm 13 in. Total range: 391.5 mm 15.4 in.
Reel fore and aft	Cylinder stroke: 359 mm 14.1 in. Total range: 620 mm 24.4 in.
Fore of the cutterbar
Reel resume	Base
Reel reverse	Base
Operating speeds	6-54 rpm
Operating speeds (54-in. reel)	5-44 rpm

Number of slats
Diameter
Height control
Speed control
Operating speeds

Width	Rubber coated polyester with V-Guide tracking: 0.7 L 24 oz Side belts: 1.02 m 3.33 ft Center belts: 1.4 m 4.583 ft Center belt not included with SPW configuration
Belt depth
Cleat height	25.4 mm 1 in.
Operating speed	Side belts: variable up to 223 m/min 735 fpm Center belts: 212 m/min 695 fpm Center belt not included with SPW configuration
Speed control	Hydraulic from cab
Center belt reverse	Base: center belt not included with SPW configuration

Diameter	Two factory-installed options: 356 or 406 mm 14 or 16 in. Feed drum not included with SPW configuration
Feed drum fingers	Heavy-duty and round with breakaway notch and retainer Diameter: 16 mm 0.625 in.
Number of fingers	18
Auger finger platform	Dual chevron, retracting
Finger reach	152 mm 6 in.
Drum/auger reverse	Base
Operating speed	195 rpm
Center cleanout door	Base

Type	Base: electrohydraulic
Header height sensing on the ground	Base
Header height sensing off the ground	Base

Type	Optional: hydraulic drive
Fingered augers
Size

Platform length	10.0 m 32.9 ft
Overall operating depth	2.5 m 8.2 ft
Transport width, field position	9.9 m 32.5 ft
Transport width on wheel, less dividers	2.7 m 8.9 ft
Transport length, hitch extended	12.3 m 40.4 ft